Search Results

The confluence of increasing fuel economy requirements and increased use of ethanol as a gasoline blend component has led to various studies into the efficiency and performance benefits of higher octane numbers and high ethanol content fuels in modern engines. As part of a comprehensive study of the autoignition of different fuels in both the CFR octane rating engine and a modern, direct injection, turbocharged spark-ignited engine, a series of fuel blends were prepared with varying composition, octane numbers and ethanol blend levels. The paper reports on the third part of this study where cylinder pressures were recorded for fuels under knocking conditions in both a single-cylinder research engine (SCE), utilizing a GM LHU head and piston, as well as the CFR engines used for octane ratings.

It is widely acknowledged that the CFR octane rating engines are not representative of modern engines and that there is a gap in the quantification of knock severity between the two engine types. As part of a comprehensive study of the autoignition of different fuels in both the CFR octane rating engines and a modern, direct injection, turbocharged spark-ignited engine, a series of fuel blends were tested with varying composition, octane numbers and ethanol blend levels. The paper reports on the fourth part of this study where cylinder pressures were recorded under standard knock conditions in CFR engines under RON and MON conditions using the ASTM prescribed instrumentation. By the appropriate signal conditioning of the D1 detonation pickups on the CFR engines, a quantification of the knock severity was possible that had the same frequency response as a cylinder pressure transducer.

Alternative fuels are being evaluated in automotive applications in both commercial and government fleets in an effort to reduce emissions and United States dependence on diesel fuel. Vehicles and equipment have been operated using 100 percent biodiesel and various blends of biodiesel and diesel fuel in a variety of applications, including farming equipment and transit buses. This government study investigates the compatibility of four base fuels and six blends with elastomer and metallic components commonly found in fuel systems. The physical properties of the elastomers were measured according to American Society of Testing and Materials (ASTM) D 471, “Standard Test Method for Rubber Property-Effect of Liquids,” and ASTM D 412, “Standard Test Methods for Rubber Properties in Tension.” These evaluations were performed at 51.7°C for 0, 22, 70, and 694 hours. Tensile strength, hardness, swell, and elongation were determined for all specimens.

Water injection has been used to reduce the charge temperature and mitigate knocking due to its higher latent heat of vaporization compared to gasoline fuel. When water is injected into the intake manifold or into the cylinder, it evaporates by absorbing heat energy from the surrounding and results in charge cooling. However, the effect of detailed evaporation process on the combustion characteristics under gasoline direct injection relevant conditions still needs to be investigated. Therefore, spray study was firstly conducted using a multi-hole injector by injecting pure water and water-methanol mixture into constant volume combustion chamber (CVCC) at naturally aspirated and boosted engine conditions. The target water-fuel ratio was fixed at 0.5. Mie-scattering and schlieren images of sprays were analyzed to study spray characteristics, and evaluate the amount of water vaporization.

This paper describes the results of a study that examined the mechanism of phased perturbation as an emissions control technique. Phased perturbation involves independently controlling the fuel delivered to each bank of a dual bank engine (or each cylinder of a single manifold engine), which allows the two banks to have an adjustable, relative Air/Fuel (A/F) perturbation phase-shift from one another. The phase shifted exhaust is then recombined to achieve a near stoichiometric mixture prior to entering a single underbody catalyst. Phase shifting the exhaust Air/Fuel ratio creates a situation in which both rich exhaust constituents (unburnt hydrocarbons and carbon monoxide) and lean exhaust constituents (oxygen and oxides of nitrogen) arrive at the catalyst at the same time. The results of the study showed that phased perturbation produced a significant effect on A/F control and catalyst THC, CO, and NOx efficiency.

Recent internal research performed at SwRI examined an emissions control mechanism that we have labeled, ‘phased A/F perturbation.’ The suggested mechanism of phased perturbation involves independently controlling the fuel delivered to each bank of a dual bank engine, which allows the two banks to have an adjustable, relative A/F perturbation phase-shift from one another. Exhaust from the two banks can be combined to achieve a near-stoichiometric mixture prior to entering a single underbody catalyst. Since both rich and lean exhaust species would be present simultaneously, a highly reactive mixture would continuously enter the catalyst. In that work, it was found that A/F phasing produced as significant an effect on conversion efficiency as perturbation amplitude and frequency, i.e. A/F phasing was identified as a third dimension for optimization of exhaust gas composition as it enters the catalyst.

Excessive wear and malfunctions in fluid power handling systems are often caused by contaminants or small particles that may be built-in, self-generated, or ingested from the environment. Filtration subsystems in such systems are designed to prevent these problems from happening. However, machine performance degradation, shortened service life, and even catastrophic failures are occasionally encountered in the real world. Then, what is the missing linkage? This paper tries to address the issue using a multi-disciplinary approach that employs failure analyses, laboratory experimentation, predictive correlation, and concurrent engineering with an emphasis on contaminant characterization and filtration strategies. Practical contamination analysis methodologies are discussed via examples and case studies.

Hydrotreating of vegetable oils or animal fats is an alternative process to esterification for producing biobased diesel fuels. Hydrotreated products are also called renewable diesel fuels. Hydrotreated vegetable oils (HVO) do not have the detrimental effects of ester-type biodiesel fuels, like increased NOx emission, deposit formation, storage stability problems, more rapid aging of engine oil or poor cold properties. HVOs are straight chain paraffinic hydrocarbons that are free of aromatics, oxygen and sulfur and have high cetane numbers. In this paper, NOx - particulate emission trade-off and NOx - fuel consumption trade-off are studied using different fuel injection timings in a turbocharged charge air cooled common rail heavy duty diesel engine. Tested fuels were sulfur free diesel fuel, neat HVO, and a 30% HVO + 70% diesel fuel blend. The study shows that there is potential for optimizing engine settings together with enhanced fuel composition.

This program involved the detailed evaluation of a novel laser-based in-exhaust ammonia sensor using a diesel fuel-based burner platform integrated with an ammonia injection system. Test matrix included both steady-state modes and transient operation of the burner platform. Steady-state performance evaluation included tests that examined impact of exhaust gas temperature, gas velocity and ammonia levels on sensor response. Furthermore, cross sensitivity of the sensor was examined at different levels of NOX and water vapor. Transient tests included simulation of the FTP test cycles at different ammonia and NOX levels. A Fourier transform infrared (FTIR) spectrometer as well as NIST traceable ammonia gas bottles (introduced into the exhaust stream via a calibrated flow controller) served as references for ammonia measurement.

A recently developed in-cylinder fuel injection probe was used to deposit a small amount of liquid fuel on various surfaces within the combustion chamber of a 4-valve engine that was operating predominately on liquefied petroleum gas (LPG). A fast flame ionization detector (FFID) was used to examine the engine-out emissions of unburned and partially-burned hydrocarbons (HCs). Injector shut-off was used to examine the rate of liquid fuel evaporation. The purpose of these experiments was to provide insights into the HC formation mechanism due to in-cylinder wall wetting. The variables investigated were the effects of engine operating conditions, coolant temperature, in-cylinder wetting location, and the amount of liquid wall wetting. The results of the steady state tests show that in-cylinder wall wetting is an important source of HC emissions both at idle and at a part load, cruise-type condition. The effects of wetting location present the same trend for idle and part load conditions.

Piston ring and liner wear measurements and analyses were performed in a production 3.6L V6 gasoline engine with radiolabelled engine parts. Three isotopes were generated: one in the engine liner using surface layer activation; one each in the top ring face and top ring side using bulk activation. Real-time wear measurements and subsequent rates of these three surfaces were captured using the radioactive decay of the isotopes into the engine oiling system. In addition, surface roughness and wear profile measurements were carried out using white light interferometry. The results from Phase I provided insights on evolution of wear and wear rates in critical engine components in a gasoline engine. Phase II will extend this work further and focus on evaluating the fuel additive effects on engine wear.

Fuel additives are being used more frequently to meet “premium diesel fuel” requirements. Although these additives improve performance, they also affect the water separation characteristics. This program was designed to determine the effects of various additives on fuel/water separation in low- and ultra-low sulfur diesel fuel. The additives studied include detergents and lubricity additives. A soy-based biofuel is also considered. The fuel/water separation tests conducted with coalescer filter technology generally produced higher efficiencies while the addition of a detergent additive package at 175-ppm generally produced lower water separation efficiencies.

Aftertreatment durability demonstration is a required validation exercise for on-road medium and heavy-duty diesel engine certification. The demonstration is meant to validate emissions compliance for the engine and aftertreatment system at full useful life or FUL. Current certification practices allow engine manufacturers to complete partial aging and then extrapolate emissions performance results to FUL. While this process reduces the amount of service accumulation time, it does not consider changes in the aftertreatment deterioration rate. Rather, deterioration is assumed to occur at a linear rate, which may lead to false conclusions relating to emissions compliance. With CARB and EPA’s commitment to the reduction of criteria emissions, emphasis has also been placed on revising the existing certification practices. The updated practices would require engine manufacturers to certify with an aftertreatment system aged to FUL.

The medium and heavy-duty powertrain industry trend is to reduce reliance on diesel fuel and is aligned with continued efforts of achieving ultra-low emissions and high brake efficiencies. Compression Ignition (CI) of late cycle Directly Injected (DI) Natural Gas (NG) shows the potential to match diesel performance in terms of brake efficiency and power density, with the benefit of utilizing a lower carbon content fuel. A primary challenge is to achieve stable ignition of directly injected NG over a wide engine speed and load range without the need for a separate ignition source. This project aims to demonstrate the CI of DI NG through experimental studies with a Single Cylinder Research Engine (SCRE), leading to the development of a mono-fueled NG engine with equivalent performance to that of current diesel technology, 25% lower CO2 emissions, and low engine out methane emissions.

Stringent emissions regulations and the need for lower tailpipe emissions are pushing the development of low-carbon alternative fuels. H2 is a zero-carbon fuel that has the potential to lower CO2 emissions from internal combustion engines (ICEs) significantly. Moreover, this fuel can be readily implemented in ICEs with minor modifications. Batteries can be argued to be a good zero tailpipe emission solution for the light-duty sector; however, medium and heavy-duty sectors are also in need of rapid decarbonization. Current strategies for H2 ICEs include modification of the existing spark ignition (SI) engines to run on port fuel injection (PFI) systems with minimal changes from the current compressed natural gas (CNG) engines. This H2 ICE strategy is limited by knock and pre-ignition. One solution is to run very lean (lambda >2), but this results in excessive boosting requirements and may result in high NOx under transient conditions.